How to install curtain rods
Sophia Carter
Published Jan 06, 2026
Where should curtain rod brackets be placed?
Each bracket should be placed at the height you previously determined and about four to six inches from the side of the window frame. (This will allow you to open the curtains completely.) Check to make sure your pencil marks are level otherwise the entire window treatment will be crooked.How do you install curtain rod brackets?
Do you need a drill to install curtain rods?
If you don’t own a drill or cannot perform this kind of major installation in a rented space, tension curtain rods are a great option for hanging curtains between two walls. Here’s how to install them: Measure the space between your two walls. You‘ll want to buy a rod that’s a little bit longer than this measurement.What is the proper height to hang a curtain rod?
A rule of thumb (from Architectural Digest) is that curtains should be hung between four to six inches above the window frame, so install your curtain rod accordingly. When you hang the curtain rod high, it will make the window appear taller.How high should a curtain rod be for 84 inch curtains?
The length of the curtain dictates the height of the rod. If you buy 84–inch-long curtains, the rod must be mounted roughly 84 inches from the floor if the curtains hang from the rod without rings. This lets the hem of the curtains brush the floor.How do you hang a curtain rod with Command hooks?
Mark on the wall with a pencil where you want to place the Command hooks. Place the Command hook against the wall where you want it to go, then trace the top, bottom, and side edges with a pencil. Place all of the hooks 4 to 6 inches (10 to 15 cm) above the frame.Can you use Command Strips for curtain rods?
Reusing them is as easy as applying a Command™ Refill Strip, so you can take down, move and reuse them again and again! Great for installing curtain rods or hanging wall décor, coats, and bags! Use with rod diameter less than 5/8 in, length less than 48 in, and finial greater than 3/4 in.Can I use Command strips to hang curtains?
After you’ve carefully measured your curtains, mark your wall where each hook will adhere. Peel off the Command strip adhesive and apply it to the hook. Press the Command Hook firmly onto the wall for at least 30 seconds, and repeat with the other hook. Wait at least 30 minutes before hanging your curtains.What is the strongest command hook?
Jumbo hooks allow you to hold up to 7.5 pounds! Using the revolutionary Command™ Adhesive, Command™ Decorative Hooks hold strongly on a variety of surfaces, including paint, wood, tile and more.Command™ Jumbo Quartz Hook.
| Attribute Name | Value |
|---|---|
| Size | Jumbo |
| Weight Capacity | 7-1/2 pounds |
Can Command Strips hold mirrors?
The 3M Command™ Large Picture & Mirror Hanging Strips, holds 1.8kg for each pair of strips used and are perfect for easily wall mounting OurBoards, mirrors and pictures. No drilling and no need for a skilled maintenance person. One individual can mount the item on the wall.How do you hang something heavy without nails?
You can use picture hangers and plastic anchors to hang small or lighter weight photos or pictures. Don’t use them for towel racks, which can pull away from the wall, especially if people put weight on the bar. Picture hangers have little metal hooks through which a small nail passes into the drywall.Can you combine command strips to hold more weight?
If the hook base is wide enough for it, the instructions usually indicate to put strips side by side, and also indicate it can hold double the weight on the hook packages. Perhaps this is obvious, but you can NOT double the weight by layering two strips.How much weight can 2 Command Strips hold?
The large strips can handle a 24-inch to 36-inch object that weighs up to 16 pounds. The smaller hanging strips can only handle up to 4 pounds.Do you have to wait an hour for Command strips?
Why do I have to wait an hour before using the product? The one-hour wait ensures that the adhesive has had enough time to build strong adhesion to the wall or surface.How do you hang something heavy with command strips?
Why won’t my command strips stick?
Any dust, dirt, or residue can make it hard for the adhesive to form a strong bond. I recommend cleaning the area with a Magic Eraser, because it’s quick and easy, and will thoroughly clean most surfaces. After using the Magic Eraser, wipe the area with rubbing alcohol to leave it squeaky clean.What can I use instead of Command strips?
Consider these alternatives if you wish to transform your apartment.- Command Strips. Command strips offer an easy substitute to hammers and nails for hanging a picture.
- Adhesive Hooks.
- Wall Anchor.
- Pogo.
- Drywall Hooks.
- Hardwall Hangers.
- Final Thoughts.
How much weight can Medium Command Strips hold?
Command Medium Picture Hanging Strips| Attribute Name | Value |
|---|---|
| Material | Foam |
| Package Contents | 2 Pairs of Strips, 3 Pairs of Strips, 52 Pairs of Strips, 6 strips |
| Size | Medium |
| Weight Capacity | 3 pounds |
What is the heaviest weight command strips can hold?
Command Large Picture Hanging Strips| Attribute Name | Value |
|---|---|
| Material | Foam |
| Package Contents | 14 Pairs of Strips, 3 Pairs of Strips, 4 pairs of strips, 4 Sets of Strips, 6 pairs of strips, 8 Strips |
| Size | Large |
| Weight Capacity | 16 pounds |
Do Command strips ruin walls?
One click tells you Picture Hanging Strips are locked in and holding tight. Best of all, when you are ready to take down or move your pictures, they come off cleanly—no nail holes, cracked plaster or sticky residue. Learn the proper way to remove Command™ Picture Hanging Strips so they won’t damage your wall.How many pounds do small command strips hold?
Command Small Picture Hanging Strips, Holds up to 4 lbs., 4-Pairs per Pack, 9-Packs (36-Pairs Total), Indoor Use.How do you attach Command strips to the wall?
Holds -20°F to 125°F.- Wipe wall with rubbing alcohol. Do not use household cleaners or water, as they can leave slippery residue.
- Separate strips. Remove red liner. Press adhesive to hook.
- Remove black liner. Press hook firmly to wall for 30 seconds. If you can see the tab of the strip, you are all done!
How do you stick 3m Command strips?
To ensure adhesive hold, temporarily remove frame from wall to reinforce strips. Peel frame as shown.Easy On
- Wipe wall with rubbing alcohol. Do not use household cleaners or water.
- Separate strips. Click strips together.
- Remove one side of liners. Stick on frame as shown. Press firmly.
